Wakeboarder Forum Index

 
 FAQFAQ   SearchSearch   MemberlistMemberlist   StatisticsStats   FavoritesFavorites   RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages  Log inLog in 
BlogsBlogs   

Boatmate Trailer and Boat Buddy

 
Post new topic   Reply to topic    Wakeboarder Forum Index -> Wakeboard Boat General Discussion
View previous topic :: View next topic  
Author Message
jonyb
Addict
Addict


Joined: 06 Oct 2007
Posts: 844
City: Paducah

PostPosted: Aug 04, 2008 7:11 am    Post subject: Boatmate Trailer and Boat Buddy Reply with quote

This Boat Buddy thing is junk! If you set the pin to catch when you load the boat, then the truck pulls the trailer out of the water, the bow loop pulls back against the pin and it's nearly impossible to release it next time you launch. Not to mention how well that rubber (that doesn't roll or move) holds the boat off the trailer. When the rubber binds against the fiberglass of the boat it gets in a bind and won't let the boat go any higher. I have to get my driver to back the boat down to wet the bunks, pull up to where the fenders are at water level, get the boat on the bunks so it's straight, pull the boat up to get the bow up in the air or the same angle as the trailer, back the trailer in further while motoring the boat up to the bow stop, then winch it up the rest of the way. It's seriously a PITA.

Now the big problem: The 2 upright pieces that the BB bolts to are bent, bad! I don't know what happened when it was loaded, but now it's bent so bad that it ruined the rubber part of the boat buddy.

Is there a good replacement for this? Maybe a small roller like everyone else uses?
Back to top
View user's profile Send private message
Commodore
Ladies Man
Ladies Man


Joined: 20 Jun 2005
Posts: 11636

PostPosted: Aug 04, 2008 8:23 am    Post subject: Reply with quote

jonyb, I bought a big urethane roller from a boat supply. Works great, as I hated my boat buddy, and since my bow is so low the boat buddy would go above the bow and gash the hell out of it. Roller works great now.
Back to top
View user's profile Send private message
jonyb
Addict
Addict


Joined: 06 Oct 2007
Posts: 844
City: Paducah

PostPosted: Aug 04, 2008 10:36 am    Post subject: Reply with quote

haugy wrote:
jonyb, I bought a big urethane roller from a boat supply. Works great, as I hated my boat buddy, and since my bow is so low the boat buddy would go above the bow and gash the hell out of it. Roller works great now.

You probably didn't notice when I was down there, but mine is gashed pretty bad too. Same problem as you had.
Back to top
View user's profile Send private message
tonality
Soul Rider
Soul Rider


Joined: 20 Aug 2004
Posts: 435
City: DFW

PostPosted: Aug 05, 2008 7:12 am    Post subject: Reply with quote

Had my dealer replace the BB with the roller before i even drove the new boat off the lot...hate those freakin things. Just toss a good size roller on there, you'll be good to go.
_________________
<insert witty banter here>
Back to top
View user's profile Send private message Visit poster's website AIM Address
fast4winns
Newbie
Newbie


Joined: 26 Dec 2007
Posts: 8
City: St. Louis

PostPosted: Aug 05, 2008 9:50 am    Post subject: Boatmate Trailer and Boat Buddy Reply with quote

I just bought a '06 Supra and the 2nd time I took it out I "f'ed" up my trailer and scratched my boat because of this horrible invention.

I was thinking about replacing it with a roller but my dealer suggested I add bigger bunks on the front hoping that will help.

I'm taking it out on Friday so we'll see.

I'll keep you posted.
Back to top
View user's profile Send private message Send e-mail
WakeMikey
Addict
Addict


Joined: 29 Mar 2008
Posts: 640
City: Fridley

PostPosted: Aug 05, 2008 10:44 am    Post subject: Reply with quote

Post a pic please of what you mean by 'roller'. I have a boat buddy that came with my 87 Supra SunSport trailer (matching trailer from Supra). The only real problems I have had involve the locking pin mechanism.

The pin isn't really secured to anything and can fall out (and into the lake) if I'm not careful. When I put the boat on the trailer, it goes on real nice and easy as long as I back in far enough. But when the pin is successfully clicked into the D-ring, I find that the pin isn't securly fastened in the opposite plate. It has a little hole that the end of the pin should be sitting in but it just hits the plate crooked. Worked fine though so far...

_________________
1987 Supra SunSport
Back to top
View user's profile Send private message
ridininmd
Wakeboarder.Commie
Wakeboarder.Commie


Joined: 16 Feb 2006
Posts: 1231

PostPosted: Aug 05, 2008 12:02 pm    Post subject: Reply with quote

Once I got mine figured out I loved it. You just have to get the trailer right, and then drive on, pin locks, and away you go. Just remember to pull the pin and hook up the winch strap before driving or you will bend it up and it won't work right anymore.
Back to top
View user's profile Send private message
Commodore
Ladies Man
Ladies Man


Joined: 20 Jun 2005
Posts: 11636

PostPosted: Aug 05, 2008 12:03 pm    Post subject: Reply with quote

WakeMikey, here's what I have in place of the boat buddy. I have found the black ones make marks on the hull, so I went with clear/amber urethane



http://www.boatersworld.com/product/369171632.htm?bct=t13098025%3Bcitrailering%3Bcibunks-rollers%3Bcirollers
Back to top
View user's profile Send private message
jonyb
Addict
Addict


Joined: 06 Oct 2007
Posts: 844
City: Paducah

PostPosted: Aug 05, 2008 12:52 pm    Post subject: Reply with quote

ridininmd wrote:
Once I got mine figured out I loved it. You just have to get the trailer right, and then drive on, pin locks, and away you go. Just remember to pull the pin and hook up the winch strap before driving or you will bend it up and it won't work right anymore.

The problem right there is that when the truck starts pulling the boat out of the water, the boat pulls back against the pin putting it in a bind, so then it's nearly impossible to pull the pin back out.
Back to top
View user's profile Send private message
ridininmd
Wakeboarder.Commie
Wakeboarder.Commie


Joined: 16 Feb 2006
Posts: 1231

PostPosted: Aug 05, 2008 10:28 pm    Post subject: Reply with quote

jonyb, Help the truck up the ramp with the boat, that will keep you far enough forward on the pin the keep it from binding up. Like I said you gotta figure it out, but once you've got it down you'll never want to be without it.
Back to top
View user's profile Send private message
jonyb
Addict
Addict


Joined: 06 Oct 2007
Posts: 844
City: Paducah

PostPosted: Aug 06, 2008 6:19 am    Post subject: Reply with quote

My luck with that would be starving the water pump and burning up the impeller.
Back to top
View user's profile Send private message
Commodore
Ladies Man
Ladies Man


Joined: 20 Jun 2005
Posts: 11636

PostPosted: Aug 06, 2008 9:07 am    Post subject: Reply with quote

jonyb, or having a deep ramp like mine and the boat swings enough to bang the bunks, or have the boat come down above a wheel well and either bash the boat or the wheel well.

That's not a good idea to try. I'll take my extra 10 seconds and use the strap. Mr. Green
Back to top
View user's profile Send private message
02LaunchSSV
Newbie
Newbie


Joined: 04 Mar 2005
Posts: 8

PostPosted: Aug 06, 2008 3:40 pm    Post subject: Reply with quote

Same problem here with my 02 and now working on a bow stop setup like the older Nautiques and Mastercrafts. Woody at SE Correct Craft was a huge help along with the forums at correctcraftfan.com. Good luck with yours but planning on eliminating mine!
Back to top
View user's profile Send private message
Riddick
Outlaw
Outlaw


Joined: 14 Feb 2008
Posts: 212
City: Knoxville

PostPosted: Aug 06, 2008 6:34 pm    Post subject: Reply with quote

jonyb, -once pin fires, use crank to relieve the pin of the boat's weight
(thus making you able to move pin to the unlocked position easily)
-when getting ready to put in, unlock the pin first, then undo the
crank ( this will make your impossible task possible)
Back to top
View user's profile Send private message
miked
Soul Rider
Soul Rider


Joined: 26 May 2004
Posts: 282
City: nor cal

PostPosted: Aug 06, 2008 6:50 pm    Post subject: Reply with quote

if you have to strap and winch the boat anyways after it latches then whats the use. might as well throw that boat damaging pos away. My 02
Back to top
View user's profile Send private message
jonyb
Addict
Addict


Joined: 06 Oct 2007
Posts: 844
City: Paducah

PostPosted: Aug 06, 2008 8:14 pm    Post subject: Reply with quote

miked wrote:
if you have to strap and winch the boat anyways after it latches then whats the use. might as well throw that boat damaging pos away. My 02

EXACTLY!! I'm taking the boat down to the river tomorrow to try and straighten the bent stuff. I may just pick up a roller tomorrow too.
Back to top
View user's profile Send private message
Commodore
Ladies Man
Ladies Man


Joined: 20 Jun 2005
Posts: 11636

PostPosted: Aug 07, 2008 5:02 am    Post subject: Reply with quote

02LaunchSSV, I know what your talking about. The Bow planks right? The two upright carpeted boards the actually stop the boats bow in a padded V-shape.
When I was looking for another trailer, I was looking for a CC trailer just for those two pieces.

Swapping mine out took 10 minutes. Takes two crescent wrenches, and you're done. Since your trailer is pretty new you shouldn't need a new bolt, but if I were you, I'd disassemble the Boat buddy and see what kind of bolt runs through it so you can make sure it will run through the Urethane rollers as well.
Back to top
View user's profile Send private message
brew
Wakeboarder.com Freak
Wakeboarder.com Freak


Joined: 09 Aug 2005
Posts: 2778
City: Jackson

PostPosted: Aug 09, 2008 1:43 pm    Post subject: Reply with quote

I hate the p.o.s. on my trailer. I have to back my truck into the water until the bumper is about in the water and then get up under the boat and lift the boat to get the pin to release from it's severely stuck position. Then when I get finished for the day I have to barely get the bunks in the water to keep my boat from shooting under the boat buddy and really getting me in a bind. Part of the problem is a shallow ramp, but I've never had this much trouble with a trailer without a boat buddy on it.
Back to top
View user's profile Send private message
tonality
Soul Rider
Soul Rider


Joined: 20 Aug 2004
Posts: 435
City: DFW

PostPosted: Aug 11, 2008 12:46 pm    Post subject: Reply with quote

The boat buddy definitely made me miss my old Ziemann trailer my MB had, with the 2 boards up front (bow stops, someone was talking about earlier)...definitely would be worth it to me to either have this added or get a new trailer with them, best. option. evar.
_________________
<insert witty banter here>
Back to top
View user's profile Send private message Visit poster's website AIM Address
Display posts from previous:   
Post new topic   Reply to topic    Wakeboarder Forum Index -> Wakeboard Boat General Discussion All times are GMT - 8 Hours
Page 1 of 1

Add To Favorites

Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
             


Copyright © 2012 - Wakeboarding - Wakeboarder.com - All Right Reserved
Powered by phpBB © 2001, 2005 phpBB Group