| View previous topic :: View next topic |
| Author |
Message |
jonyb Addict


Joined: 06 Oct 2007 Posts: 844 City: Paducah
|
Posted: Aug 04, 2008 7:11 am Post subject: Boatmate Trailer and Boat Buddy |
|
|
This Boat Buddy thing is junk! If you set the pin to catch when you load the boat, then the truck pulls the trailer out of the water, the bow loop pulls back against the pin and it's nearly impossible to release it next time you launch. Not to mention how well that rubber (that doesn't roll or move) holds the boat off the trailer. When the rubber binds against the fiberglass of the boat it gets in a bind and won't let the boat go any higher. I have to get my driver to back the boat down to wet the bunks, pull up to where the fenders are at water level, get the boat on the bunks so it's straight, pull the boat up to get the bow up in the air or the same angle as the trailer, back the trailer in further while motoring the boat up to the bow stop, then winch it up the rest of the way. It's seriously a PITA.
Now the big problem: The 2 upright pieces that the BB bolts to are bent, bad! I don't know what happened when it was loaded, but now it's bent so bad that it ruined the rubber part of the boat buddy.
Is there a good replacement for this? Maybe a small roller like everyone else uses? |
|
| Back to top |
|
 |
|
|
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Aug 04, 2008 8:23 am Post subject: |
|
|
| jonyb, I bought a big urethane roller from a boat supply. Works great, as I hated my boat buddy, and since my bow is so low the boat buddy would go above the bow and gash the hell out of it. Roller works great now. |
|
| Back to top |
|
 |
jonyb Addict


Joined: 06 Oct 2007 Posts: 844 City: Paducah
|
Posted: Aug 04, 2008 10:36 am Post subject: |
|
|
| haugy wrote: | | jonyb, I bought a big urethane roller from a boat supply. Works great, as I hated my boat buddy, and since my bow is so low the boat buddy would go above the bow and gash the hell out of it. Roller works great now. |
You probably didn't notice when I was down there, but mine is gashed pretty bad too. Same problem as you had. |
|
| Back to top |
|
 |
tonality Soul Rider

Joined: 20 Aug 2004 Posts: 435 City: DFW
|
Posted: Aug 05, 2008 7:12 am Post subject: |
|
|
Had my dealer replace the BB with the roller before i even drove the new boat off the lot...hate those freakin things. Just toss a good size roller on there, you'll be good to go. _________________ <insert witty banter here> |
|
| Back to top |
|
 |
fast4winns Newbie

Joined: 26 Dec 2007 Posts: 8 City: St. Louis
|
Posted: Aug 05, 2008 9:50 am Post subject: Boatmate Trailer and Boat Buddy |
|
|
I just bought a '06 Supra and the 2nd time I took it out I "f'ed" up my trailer and scratched my boat because of this horrible invention.
I was thinking about replacing it with a roller but my dealer suggested I add bigger bunks on the front hoping that will help.
I'm taking it out on Friday so we'll see.
I'll keep you posted. |
|
| Back to top |
|
 |
WakeMikey Addict


Joined: 29 Mar 2008 Posts: 640 City: Fridley
|
Posted: Aug 05, 2008 10:44 am Post subject: |
|
|
Post a pic please of what you mean by 'roller'. I have a boat buddy that came with my 87 Supra SunSport trailer (matching trailer from Supra). The only real problems I have had involve the locking pin mechanism.
The pin isn't really secured to anything and can fall out (and into the lake) if I'm not careful. When I put the boat on the trailer, it goes on real nice and easy as long as I back in far enough. But when the pin is successfully clicked into the D-ring, I find that the pin isn't securly fastened in the opposite plate. It has a little hole that the end of the pin should be sitting in but it just hits the plate crooked. Worked fine though so far... _________________ 1987 Supra SunSport |
|
| Back to top |
|
 |
ridininmd Wakeboarder.Commie


Joined: 16 Feb 2006 Posts: 1231
|
Posted: Aug 05, 2008 12:02 pm Post subject: |
|
|
| Once I got mine figured out I loved it. You just have to get the trailer right, and then drive on, pin locks, and away you go. Just remember to pull the pin and hook up the winch strap before driving or you will bend it up and it won't work right anymore. |
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
|
| Back to top |
|
 |
jonyb Addict


Joined: 06 Oct 2007 Posts: 844 City: Paducah
|
Posted: Aug 05, 2008 12:52 pm Post subject: |
|
|
| ridininmd wrote: | | Once I got mine figured out I loved it. You just have to get the trailer right, and then drive on, pin locks, and away you go. Just remember to pull the pin and hook up the winch strap before driving or you will bend it up and it won't work right anymore. |
The problem right there is that when the truck starts pulling the boat out of the water, the boat pulls back against the pin putting it in a bind, so then it's nearly impossible to pull the pin back out. |
|
| Back to top |
|
 |
ridininmd Wakeboarder.Commie


Joined: 16 Feb 2006 Posts: 1231
|
Posted: Aug 05, 2008 10:28 pm Post subject: |
|
|
| jonyb, Help the truck up the ramp with the boat, that will keep you far enough forward on the pin the keep it from binding up. Like I said you gotta figure it out, but once you've got it down you'll never want to be without it. |
|
| Back to top |
|
 |
jonyb Addict


Joined: 06 Oct 2007 Posts: 844 City: Paducah
|
Posted: Aug 06, 2008 6:19 am Post subject: |
|
|
| My luck with that would be starving the water pump and burning up the impeller. |
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Aug 06, 2008 9:07 am Post subject: |
|
|
jonyb, or having a deep ramp like mine and the boat swings enough to bang the bunks, or have the boat come down above a wheel well and either bash the boat or the wheel well.
That's not a good idea to try. I'll take my extra 10 seconds and use the strap.  |
|
| Back to top |
|
 |
02LaunchSSV Newbie

Joined: 04 Mar 2005 Posts: 8
|
Posted: Aug 06, 2008 3:40 pm Post subject: |
|
|
| Same problem here with my 02 and now working on a bow stop setup like the older Nautiques and Mastercrafts. Woody at SE Correct Craft was a huge help along with the forums at correctcraftfan.com. Good luck with yours but planning on eliminating mine! |
|
| Back to top |
|
 |
Riddick Outlaw

Joined: 14 Feb 2008 Posts: 212 City: Knoxville
|
Posted: Aug 06, 2008 6:34 pm Post subject: |
|
|
jonyb, -once pin fires, use crank to relieve the pin of the boat's weight
(thus making you able to move pin to the unlocked position easily)
-when getting ready to put in, unlock the pin first, then undo the
crank ( this will make your impossible task possible) |
|
| Back to top |
|
 |
miked Soul Rider

Joined: 26 May 2004 Posts: 282 City: nor cal
|
Posted: Aug 06, 2008 6:50 pm Post subject: |
|
|
| if you have to strap and winch the boat anyways after it latches then whats the use. might as well throw that boat damaging pos away. My 02 |
|
| Back to top |
|
 |
jonyb Addict


Joined: 06 Oct 2007 Posts: 844 City: Paducah
|
Posted: Aug 06, 2008 8:14 pm Post subject: |
|
|
| miked wrote: | | if you have to strap and winch the boat anyways after it latches then whats the use. might as well throw that boat damaging pos away. My 02 |
EXACTLY!! I'm taking the boat down to the river tomorrow to try and straighten the bent stuff. I may just pick up a roller tomorrow too. |
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Aug 07, 2008 5:02 am Post subject: |
|
|
02LaunchSSV, I know what your talking about. The Bow planks right? The two upright carpeted boards the actually stop the boats bow in a padded V-shape.
When I was looking for another trailer, I was looking for a CC trailer just for those two pieces.
Swapping mine out took 10 minutes. Takes two crescent wrenches, and you're done. Since your trailer is pretty new you shouldn't need a new bolt, but if I were you, I'd disassemble the Boat buddy and see what kind of bolt runs through it so you can make sure it will run through the Urethane rollers as well. |
|
| Back to top |
|
 |
brew Wakeboarder.com Freak

Joined: 09 Aug 2005 Posts: 2778 City: Jackson
|
Posted: Aug 09, 2008 1:43 pm Post subject: |
|
|
| I hate the p.o.s. on my trailer. I have to back my truck into the water until the bumper is about in the water and then get up under the boat and lift the boat to get the pin to release from it's severely stuck position. Then when I get finished for the day I have to barely get the bunks in the water to keep my boat from shooting under the boat buddy and really getting me in a bind. Part of the problem is a shallow ramp, but I've never had this much trouble with a trailer without a boat buddy on it. |
|
| Back to top |
|
 |
tonality Soul Rider

Joined: 20 Aug 2004 Posts: 435 City: DFW
|
Posted: Aug 11, 2008 12:46 pm Post subject: |
|
|
The boat buddy definitely made me miss my old Ziemann trailer my MB had, with the 2 boards up front (bow stops, someone was talking about earlier)...definitely would be worth it to me to either have this added or get a new trailer with them, best. option. evar. _________________ <insert witty banter here> |
|
| Back to top |
|
 |
|
|
|