| View previous topic :: View next topic |
| Author |
Message |
Doug Soul Rider

Joined: 17 Feb 2003 Posts: 329 City: Walled Lake
|
Posted: Apr 11, 2006 3:19 pm Post subject: Best adhesive for backing plate!!! |
|
|
I have a Wakeair tower on my boat. I installed it this past winter and have not used it yet. It was recommended to me to put some wood backing plates additional to the stock hardware to prevent stress cracks in the gel coat. I have fabed the plates from 1/2"plywood, and sealed them with fiberglass resin. What is the best and least messy way to adhere them to the underside for each leg of the tower? Marine-tex, 5200, ? _________________ SLIP IT ON AND RIDE IT! |
|
| Back to top |
|
 |
|
|
chavez Ladies Man


Joined: 22 Sep 2003 Posts: 27375 City: Roseville
|
Posted: Apr 11, 2006 3:24 pm Post subject: |
|
|
Plexus _________________
| Quote: | | That's Mr. Gingermex to you a$$hole. |
RIP MHL 04/25/1958 - 01/11/2006 |
|
| Back to top |
|
 |
bmartin Addict

Joined: 05 Feb 2003 Posts: 794
|
Posted: Apr 12, 2006 11:51 am Post subject: |
|
|
| The towers I have had on my boats didn't use any adhesive to bond the plate to the hull - the pressure from the bolts through the tower/hull/plate will keep that backing plate plenty tight. |
|
| Back to top |
|
 |
410fortune Soul Rider

Joined: 24 Jun 2005 Posts: 314 City: Morrison
|
Posted: Apr 12, 2006 1:22 pm Post subject: |
|
|
| You can sadwich some silicoln or marine adhesive in there if you want, but like stated above its really not needed. |
|
| Back to top |
|
 |
Swass Guest
|
Posted: Apr 12, 2006 1:36 pm Post subject: |
|
|
| I disagree. If the backing plates don't have solid, complete contact with the hull, then all you're doing is transfering the pressure points to where the plate does contact the hull. The less contact, the more pressure applied. |
|
| Back to top |
|
 |
410fortune Soul Rider

Joined: 24 Jun 2005 Posts: 314 City: Morrison
|
Posted: Apr 12, 2006 1:55 pm Post subject: |
|
|
well we assume he picked a semi flat location to mount the feet and his backing plates are flat??
I did not re-enforce the fiberglass on my Bayliner where I put the Monster tower Paws, I tow #250+ men with the tower, so far so good......
the Monster Paws are large enough I believe to work with even thinner fiberglass hulls. Time will tell..... |
|
| Back to top |
|
 |
Liquidmx Addict

Joined: 26 Jul 2004 Posts: 755 City: San Jose
|
Posted: Apr 12, 2006 5:42 pm Post subject: |
|
|
Similar question but different equipment. What type of adhesive should I use to re-glue the base of the windshield on my 89 sunsetter? It wiggles pretty good even when tightened down with the screws, and they always back out from the play it has. _________________ Hold up....Wait a minute.... Let me put some pimpin in it! mmmmph |
|
| Back to top |
|
 |
wesgardner Wakeboarder.Commie

Joined: 16 Aug 2003 Posts: 1507 City: Severna Park
|
Posted: Apr 13, 2006 4:53 am Post subject: |
|
|
Hey Liquidmx,
If you want a PERMANENT solution, use 3-M 5200, you'll pull gelcoat right off the layup underneath if you have to remove it! 5200 is urethane adhesive - very tenacious stuff indeed...
I agree with Swass, if the backing plates do not fit the hull contours, you'll need to make a "bed" - I'd use thickened epoxy and just sort of snug the bolts initially, the nonce the stuff sets, tighten the remainder of the way and you'll have a perfect fit
Wes _________________ just broad reachin' thru life... |
|
| Back to top |
|
 |
Nor*Cal Ladies Man


Joined: 12 Jan 2003 Posts: 9479 City: Sac
|
Posted: Apr 13, 2006 7:24 pm Post subject: |
|
|
Marine Tex _________________ If I agreed with you we would both be wrong. |
|
| Back to top |
|
 |
Doug Soul Rider

Joined: 17 Feb 2003 Posts: 329 City: Walled Lake
|
Posted: Apr 14, 2006 11:36 am Post subject: |
|
|
Went to Watersports and asked what they did for aftermarket tower installs. They used to take the aluminum plate and beat it to conform to the inside shape of the boat side. Now they use Bondo to fill in the gap between glass and backing plate. So I made some new backing plates, 3"x7"x1/4" aluminum, and used Bondo. Worked great. _________________ SLIP IT ON AND RIDE IT! |
|
| Back to top |
|
 |
|
|
|