Wakeboarder Forum Index

 
 FAQFAQ   SearchSearch   MemberlistMemberlist   StatisticsStats   FavoritesFavorites   RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages  Log inLog in 
BlogsBlogs   

Best adhesive for backing plate!!!

 
Post new topic   Reply to topic    Wakeboarder Forum Index -> Wakeboard Boat General Discussion
View previous topic :: View next topic  
Author Message
Doug
Soul Rider
Soul Rider


Joined: 17 Feb 2003
Posts: 329
City: Walled Lake

PostPosted: Apr 11, 2006 3:19 pm    Post subject: Best adhesive for backing plate!!! Reply with quote

I have a Wakeair tower on my boat. I installed it this past winter and have not used it yet. It was recommended to me to put some wood backing plates additional to the stock hardware to prevent stress cracks in the gel coat. I have fabed the plates from 1/2"plywood, and sealed them with fiberglass resin. What is the best and least messy way to adhere them to the underside for each leg of the tower? Marine-tex, 5200, ?
_________________
SLIP IT ON AND RIDE IT!
Back to top
View user's profile Send private message Send e-mail
chavez
Ladies Man
Ladies Man


Joined: 22 Sep 2003
Posts: 27375
City: Roseville

PostPosted: Apr 11, 2006 3:24 pm    Post subject: Reply with quote

Plexus
_________________
Quote:
That's Mr. Gingermex to you a$$hole.


RIP MHL 04/25/1958 - 01/11/2006
Back to top
View user's profile Send private message Blog Visit poster's website
bmartin
Addict
Addict


Joined: 05 Feb 2003
Posts: 794

PostPosted: Apr 12, 2006 11:51 am    Post subject: Reply with quote

The towers I have had on my boats didn't use any adhesive to bond the plate to the hull - the pressure from the bolts through the tower/hull/plate will keep that backing plate plenty tight.
Back to top
View user's profile Send private message Send e-mail
410fortune
Soul Rider
Soul Rider


Joined: 24 Jun 2005
Posts: 314
City: Morrison

PostPosted: Apr 12, 2006 1:22 pm    Post subject: Reply with quote

You can sadwich some silicoln or marine adhesive in there if you want, but like stated above its really not needed.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Swass
Guest





PostPosted: Apr 12, 2006 1:36 pm    Post subject: Reply with quote

I disagree. If the backing plates don't have solid, complete contact with the hull, then all you're doing is transfering the pressure points to where the plate does contact the hull. The less contact, the more pressure applied.
Back to top
410fortune
Soul Rider
Soul Rider


Joined: 24 Jun 2005
Posts: 314
City: Morrison

PostPosted: Apr 12, 2006 1:55 pm    Post subject: Reply with quote

well we assume he picked a semi flat location to mount the feet and his backing plates are flat??

I did not re-enforce the fiberglass on my Bayliner where I put the Monster tower Paws, I tow #250+ men with the tower, so far so good......
the Monster Paws are large enough I believe to work with even thinner fiberglass hulls. Time will tell.....
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Liquidmx
Addict
Addict


Joined: 26 Jul 2004
Posts: 755
City: San Jose

PostPosted: Apr 12, 2006 5:42 pm    Post subject: Reply with quote

Similar question but different equipment. What type of adhesive should I use to re-glue the base of the windshield on my 89 sunsetter? It wiggles pretty good even when tightened down with the screws, and they always back out from the play it has.
_________________
Hold up....Wait a minute.... Let me put some pimpin in it! mmmmph
Back to top
View user's profile Send private message
wesgardner
Wakeboarder.Commie
Wakeboarder.Commie


Joined: 16 Aug 2003
Posts: 1507
City: Severna Park

PostPosted: Apr 13, 2006 4:53 am    Post subject: Reply with quote

Hey Liquidmx,

If you want a PERMANENT solution, use 3-M 5200, you'll pull gelcoat right off the layup underneath if you have to remove it! 5200 is urethane adhesive - very tenacious stuff indeed...

I agree with Swass, if the backing plates do not fit the hull contours, you'll need to make a "bed" - I'd use thickened epoxy and just sort of snug the bolts initially, the nonce the stuff sets, tighten the remainder of the way and you'll have a perfect fit

Wes

_________________
just broad reachin' thru life...
Back to top
View user's profile Send private message Send e-mail
Nor*Cal
Ladies Man
Ladies Man


Joined: 12 Jan 2003
Posts: 9479
City: Sac

PostPosted: Apr 13, 2006 7:24 pm    Post subject: Reply with quote

Marine Tex
_________________
If I agreed with you we would both be wrong.
Back to top
View user's profile Send private message Send e-mail
Doug
Soul Rider
Soul Rider


Joined: 17 Feb 2003
Posts: 329
City: Walled Lake

PostPosted: Apr 14, 2006 11:36 am    Post subject: Reply with quote

Went to Watersports and asked what they did for aftermarket tower installs. They used to take the aluminum plate and beat it to conform to the inside shape of the boat side. Now they use Bondo to fill in the gap between glass and backing plate. So I made some new backing plates, 3"x7"x1/4" aluminum, and used Bondo. Worked great.
_________________
SLIP IT ON AND RIDE IT!
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Wakeboarder Forum Index -> Wakeboard Boat General Discussion All times are GMT - 8 Hours
Page 1 of 1

Add To Favorites

Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
             


Copyright © 2012 - Wakeboarding - Wakeboarder.com - All Right Reserved
Powered by phpBB © 2001, 2005 phpBB Group