| View previous topic :: View next topic |
| Author |
Message |
hydeout22 Criminal

Joined: 30 Apr 2006 Posts: 98 City: Toronto
|
Posted: Apr 30, 2006 7:56 am Post subject: What do you think? |
|
|
Good Morning guys,
Well, a brief background. . Picked up a wakeboard which was an impluse buy and tried it last summer at the cottage with my dads boat. I was tied off at about 3 1/2' above the water at the boat and was limited to about 53' of rope to get into the nice section of the wave. By the end of the summer I was able to jump w2s hs from the left cutting to the right. I found that it seemed like the ski rope was actually pulling me down to the boat and I could definatly feel the stretch and snap in the rope. Anyways, I played around with a few designes and this is what I came up with. See Pics....
The rope will be approx 12' above the water and I can run about 71' of rope to put me in the sweet spot of the wave. Also am going to pickup a spectra wakeboard rope which should also help. Any good stores around Toronto area? The pole is being sprayed today with automotive 2 part paint. I just have to install 2 more side cleats with steel backer and reinstall the nose hook with a backer and I am all done. Was thinking of starting with 800 lbs on the cabin floor and 200 lbs in the rear in the engine compartment to keep the center of gravity low. Will let you guys know how it works. My only concern is that the boat will want to tilt left and right when I cut out but what the heck..... trying something new. I can always cut the pole down very easily. Was going to use an 8' peice but they had a 10 so took it.
Front strap says 1800lb load with 5500lb breaking strength and the sides are 1100lb load with 3300lb breaking limit. Should be strong enough? I would have to pull 30g's on the rope to get 5500 lbs. And ideas or thoughts before I try this thing?
Do you think it will work?
Will also take pics of the wave when I get the weight balanced right. Certainly not as big as a dedicated wakeboat. Am excited about it though.
Mike

|
| Description: |
| The base plate, I think it is strong enough and will have 12 screws holding it to 2 1/4" think plywood floor. |
|
| Filesize: |
196.19 KB |
| Viewed: |
4676 Time(s) |

|
| Description: |
| The top is where the yellow strap stops, there is a 2" ball welded there on top with a slight angle down towards the rear in the direction of the rope. |
|
| Filesize: |
255.03 KB |
| Viewed: |
4676 Time(s) |

|
| Description: |
| Thought it looked like a cool shot. |
|
| Filesize: |
242.34 KB |
| Viewed: |
4676 Time(s) |
|
|
| Back to top |
|
 |
|
|
tball Wakeboarder.com Freak


Joined: 24 Feb 2004 Posts: 3953
|
Posted: Apr 30, 2006 8:47 am Post subject: |
|
|
I'm impressed with your ingenuity; pretty interesting arrangement. Personally, I think the new rope will help more than the higher towpoint, but that's just me. Can you use bolts instead of screws on the baseplate? Is there any way to move the towpoint further aft? I've never seen a tow point that far forward; I wonder how that will affect steering. The straps are more than sturdy enough, just make sure that the things they are hooked to will withstand the pulling. Let us know how it goes. Good luck.
_________________
| GOB Bluth wrote: | | It's a jetpack, Michael. What could possibly go wrong? |
|
|
| Back to top |
|
 |
krbaugh Addict


Joined: 24 Jan 2003 Posts: 758 City: Edwardsville
|
Posted: Apr 30, 2006 4:52 pm Post subject: |
|
|
I would thing it could be VERY interestng to drive if you get a wakeboarder that can pull hard!
|
|
| Back to top |
|
 |
hydeout22 Criminal

Joined: 30 Apr 2006 Posts: 98 City: Toronto
|
Posted: Apr 30, 2006 6:40 pm Post subject: |
|
|
I figured it was worth a shot. Won't know unless someone tries it. It was painted today and looks really nice as the paint really cleans it up.
I am more worried about it tilting the boat at speed when cutting out more than it pulling the boat off course but we will see. Its very easy for me to cut 2' off of it making it 8'. Will hopefully get out to try it in two weeks and will post pics of it in the water and let you know how it works.
Mike
_________________ Check out my gallery. Put some pics up of wakeskate construction and a pic of the carbon which will be my new homebuilt handle. |
|
| Back to top |
|
 |
drifter36 Addict

Joined: 25 Aug 2003 Posts: 679 City: Fargo
|
Posted: Apr 30, 2006 6:47 pm Post subject: |
|
|
get rid of the ratchet strap to the front! unless it says 1800 lb breaking point or whatever, but you have to realize that that material will stretch to almost no end! I had a homemade pylon in my I/O almost exactly the same design you have there, when I first built it my dad assured me that straps to the front would be fine...nope It streched, pole broke, everybody was Pi$$ed. redid it w/ some cable and a turnbuckle to tighten it. the only thing that might be good about yours is the poles you have running to the side, where in mine we just had cables. but still I wouldnt want to take the chance.
P.S. Mine broke w/ the cables once too...plastic coated cable...plastic coat snaped off causing the cable clamps to let go...whole floor of the boat got ripped out, we were very lucky nobody got hit. I would have been hit in the face w/ the cable if the windshield hadnt been shut.
|
|
| Back to top |
|
 |
krbaugh Addict


Joined: 24 Jan 2003 Posts: 758 City: Edwardsville
|
Posted: Apr 30, 2006 7:07 pm Post subject: |
|
|
| The problem I see is the pole is in the front of the boat so when you pull hard it will be VERY easy to roll the boat and VERY VERY easy to pull the boat off course. Because you are pulling on the fron tof the boat
|
|
| Back to top |
|
 |
sjp Criminal

Joined: 09 Apr 2003 Posts: 81 City: Mesa, AZ
|
Posted: Apr 30, 2006 8:24 pm Post subject: |
|
|
I don't know about your plan. It would make me nervous.
What are those straps tied to? The railing? How strong is that railing?
And that pole is seriously long. That makes for lots of leverage on the floor. I think there is a decent chance that one good yank on the pole would cause the screws and/or floor to rip out.
But I could be wrong
Jared
|
|
| Back to top |
|
 |
hydeout22 Criminal

Joined: 30 Apr 2006 Posts: 98 City: Toronto
|
Posted: May 01, 2006 2:25 am Post subject: |
|
|
The front strap will be hooked onto the nose ring which is used to pull the boat onto the trailer and will have an aluminum guide which will be bolted to the nose to keep the strap locked onto the nose so it does not slide off. I removed the nose hook so I can get some new nuts for it and there will be a piece of 1/4"x2 1/2" x 6 1/2" steel backer plate inside the boat.
The side straps will be hooked onto side cleats. Where the cleats are located now are too far forward so I will be installing new ones that will be about 1' behind the railing post, about 3' farther back than the one that you can see in the pic. I just hooked it onto the railing so I could get some pics of it. And there will be a 1/4"x2 1/2" x 6 1/2" steel backer plate under the side cleats inside the boat and will be an aluminum plate ontop of the fiberglass and then the cleat will be sitting ontop of that so I don't think the cleats will rip out.
Front strap that I am using has a breaking point of 5500 lbs. Do you think it will stretch that much? The largest chain at Canadian Tire has a breaking point of around 6000 or 6400 lbs something like that. Have to go with a pretty thick cable to get that breaking load. I guess its nonstretch though. Hummm, will try it and see how much it flexes. I can always replace it with a cable very easily. Would be worried about it slipping in the cable clamps.
Like I mentioned, I am worried the boat will tilt side to side because of the pole height more than it being pulled off course as it has a pretty deep V hull up front. Will also be putting in around 1000 lbs in the cabin floor which should anchor the front of the boat in the water.
I found on the net you can buy 10' pylons and this one is 1" shorter than 10' but is about 2' above the water line where its sitting in the boat so might only be 1' higher than the one you can purchase.
How much does the boat tilt side to side with these pylons? I could easily cut off in the worst case, about 2 1/2' and still have clearence which would reduce the leverage but want to see how bad it will be before I start cutting things down.
Well, nothing ventured, nothing gained. This is going to be an interesting experiment for me. 13 days to test day.
Mike
_________________ Check out my gallery. Put some pics up of wakeskate construction and a pic of the carbon which will be my new homebuilt handle. |
|
| Back to top |
|
 |
wesgardner Wakeboarder.Commie

Joined: 16 Aug 2003 Posts: 1507 City: Severna Park
|
Posted: May 01, 2006 3:55 am Post subject: |
|
|
Hey hydeout22,
Here's my 2 cents - my guess is STRETCH is the main cause of failure in these homemade pylons...mine was ALL cable except for about 3 feet of webbing/ratchet system up on the bow, my two stern lines were ALL cable NO adjustment and the bow cable was doubled until the last 3 feet, when I set my system up hard, I could "bend" my boat if I had wanted to...there was virtually NO stretch - I think there are still some pics in my gallery and Bill (of Monster Tower fame) was kind enough to put my "how to" on his DIYtower.com website. From the pic, your aft running lines might be a little TOO far aft - I think ideally, you want a perfect triangle wit hthe pole being in the center....
If it works, you'll fly! Good luck usually pylons/towers are about 7 feet off the water - the "10' pole" you see on the net might be a trade name more than the actual pole height?
As far as cable clamps - you want to clamp on the WIRE not the plastic seathing - I used NicoPress fittings for mine which can also be gotten at the home center (see my "how to" for that discussion)
Another interesting point - read my article on loads and the base plate - as long as the pole stays UPRIGHT (this is one of the reasons you don't want stretch in your rig), the loads on the baseplate are STRAIGHT DOWN - mine just sat on a "Welcome" mat on the floor of my boat - no fasteners at all - doesn't need them as long as the pole stays UPRIGHT...
Wes
_________________ just broad reachin' thru life... |
|
| Back to top |
|
 |
hydeout22 Criminal

Joined: 30 Apr 2006 Posts: 98 City: Toronto
|
Posted: May 01, 2006 2:49 pm Post subject: |
|
|
Thanks for all the info, this is great. So from what I gather, this thing should work and worse case senerio I just replace the straps with cables with turn buckels to tighten them if there is stretch.
I am trying to find that site that had that 10' pole. They had a 7' pole listed called the something or other pylon and then listed the 10' one as the extended 10' pole which will add 2-6' onto your height on your jumps so I am pretty sure that the actual pole length was 10'. For the life of me I can't find it know but if I come across it, I will difinatly post it.
Yeah, am adding 2 more side cleats. I just had the straps on the railing back there to hold it for the pictures. Will take pics when its finished. Have to pickup 2 more cleats for the side.
As far as the baseplate moving around, that is exactly what I figured, that there is only down pressure on the plate. I doubled up 2 pieces of 3/4" plywood and glued them together and that is sitting and screwed down to the fiberglassed piece of 3/4" which is in the boat. Don't worry, I didn't put any screws through the bottom of the boat......That is a storage compartment.
Man, I can't stop thinking about this thing....... The adrenaline is already pumping.
I keep thinking to myself, going from a 53' stretchy ski rope that is 3 1/2' from the water to a 71' wakeboard spectra rope that is 12 1/2' above the water and I was able to just clear the wake last year, this is going to be awesome.
Sorry for the rambling,
Oh yeah, I am at Lawrence and Allen rd. or at parents house where the boat is parked when in the city at yonge and sheppard so yeah, I think I am going to checkout board sports at eglinton for sure.
Later
Mike
_________________ Check out my gallery. Put some pics up of wakeskate construction and a pic of the carbon which will be my new homebuilt handle. |
|
| Back to top |
|
 |
pilot_ryder Wakeboarder.Commie


Joined: 15 Sep 2005 Posts: 1296 City: edmonton
|
Posted: May 01, 2006 8:14 pm Post subject: |
|
|
| Was there no tower that would fit a boat like that?
|
|
| Back to top |
|
 |
Brass Balls Newbie


Joined: 29 Apr 2006 Posts: 25 City: NorCal
|
Posted: May 01, 2006 8:23 pm Post subject: |
|
|
| Nice fabrication work.
|
|
| Back to top |
|
 |
hydeout22 Criminal

Joined: 30 Apr 2006 Posts: 98 City: Toronto
|
Posted: May 04, 2006 2:26 am Post subject: Re: What do you think? |
|
|
Here are some pics I took last night.
Also, is that how you tie the rope onto the ball, or is there another way? I know its a simple thing but just want to make sure.
9 days to test date.
Mike

|
| Description: |
|
| Filesize: |
225.36 KB |
| Viewed: |
4175 Time(s) |

|
| Description: |
|
| Filesize: |
233 KB |
| Viewed: |
4175 Time(s) |

|
| Description: |
|
| Filesize: |
164.46 KB |
| Viewed: |
4175 Time(s) |
|
|
| Back to top |
|
 |
pilot_ryder Wakeboarder.Commie


Joined: 15 Sep 2005 Posts: 1296 City: edmonton
|
Posted: May 04, 2006 5:49 pm Post subject: |
|
|
| looks real good now
|
|
| Back to top |
|
 |
|
|
|