| View previous topic :: View next topic |
| Author |
Message |
DJew Jake Wakeboarder.com Freak


Joined: 17 Sep 2003 Posts: 3907 City: Toronto
|
Posted: Apr 20, 2009 11:37 am Post subject: Is running non matching tires on a 4wd really so bad? |
|
|
Every place I goto says this is bad for your transfer case, but I just dont buy it, I mean could a 1 or 2mm radius difference wreak havoc..
I have been running dif tires up front then on the back for 4 years never a single problem _________________ They know what is what but they dono what is what they just strut. |
|
| Back to top |
|
 |
|
|
impulse Addict

Joined: 13 Jan 2003 Posts: 807 City: Snyder,TX
|
Posted: Apr 20, 2009 11:41 am Post subject: |
|
|
| I dont think its good. I have always heard its really bad, I dont have proof though. I know its lots worse to have large tires and a smaller spair and have a flat. You can jack your stuff up running 3 of 1 size and 1 of another. But to answer your question, I always run the same sizes on my 4x4s. |
|
| Back to top |
|
 |
boardordie Wakeboarder.Commie

Joined: 02 Sep 2004 Posts: 1038 City: Piqua/Ohio
|
Posted: Apr 20, 2009 11:42 am Post subject: |
|
|
HAUGY... Paging HAUGY to the non-wake forum... HAUGY
I'll let the resident expert answer, but I'd say as long as you run a match set up front and a matched set in the back you'll be fine. It's when you run 2 different sized tires on the same axle you start having issues. |
|
| Back to top |
|
 |
ridininmd Wakeboarder.Commie


Joined: 16 Feb 2006 Posts: 1231
|
Posted: Apr 20, 2009 11:44 am Post subject: |
|
|
Yes, it's bad, it's like running different gear ratios in your axles.
But depending on your transfer case and hub setup it might not really matter unless you put it in 4wd. |
|
| Back to top |
|
 |
Lop Wakeboarder.com Freak


Joined: 16 Aug 2005 Posts: 4019 City: St Louis MO
|
Posted: Apr 20, 2009 11:48 am Post subject: |
|
|
if you never use 4wd you are fine but if you often use it it will tear up your drivetrain, starting with the tires _________________
| RampageWake wrote: | | Wakeboardrumma wrote: | | have good clean honest fun without alcohol. |
After you do that, help me find me leprechaun.....  |
|
|
| Back to top |
|
 |
Bambamski Wakeboarder.com Freak

Joined: 03 Apr 2003 Posts: 4405 City: Calgary
|
Posted: Apr 20, 2009 11:54 am Post subject: |
|
|
DJew Jake,
I'm sure most on here would know for more than me for sure. I had mismatched tires on my 95 Yukon and my transfer case went a couple of years later. I don't know if that had anything to do with it or not? It wasn't a cheap fix though and I sold the truck 6 monhts later.
The mechanic said that even though I wasn't in 4 wheel drive the transfer case was always moving just not engaged. Not sure if that is truly the case but it sounded good... _________________ Don't do anything rash.....and don't do anything to get a rash... |
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Apr 20, 2009 12:12 pm Post subject: |
|
|
Yes it's bad.
With that being said. If you NEVER put it in 4wd, and the only time you do it was to pull out at a boat ramp, you will be fine. But the moment you put any speed, or turning into the mix. Your transfer case will hate you.
Now if you are really talking 1-2 mm of difference, no you will be fine. If that's 100% truth. As front tires and rear tires wear at different speeds so there has to be some tolerance. But if you are running 33" rears, and 32" fronts. Yeah, that little bit will wear it out. The bigger the difference in tire size, the faster it will go KABOOM.
Imagine that you are driving your rear wheels are turning at 5,000 revolutions per minute. And that your front is wanting to turn at 5,500 revolutions per minute since they are smaller tires. Not only are your tires going to eat themselves alive. But your transfer case is taking the 3800lb load of your truck pulling against those gears. (or in some cases on the chains).
Your basically taking something that connects the front and back. And then wanting to turn the back faster than the front. Yeah it's bad.
Now, with that being said, many AWDs would be able to tolerate this better since they are equipped with a viscous coupling which allows for different wheel speeds. Which allows it to operate under any condition. But even then, the difference in tire size would cause premature wear and tear.
So in short......well long, match them up. |
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Apr 20, 2009 12:16 pm Post subject: |
|
|
Bambamski, he's half right. Depending on the vehicle. Many of the modern 4wds don't have lockout hubs. (The bubs you had to get out, go to the front and lock in). And since they don't have lockouts, when the front wheels turn, the axles turn, causing the driveshaft to turn, which spins inside the case. But it should free spin inside the case. Meaning it wouldn't matter. Many Grand Cherokees, and such have a vacuum engaged front axle meaning the front driveshaft won't turn even while driving.
My jeep has lockouts. My front driveshaft doesn't spin when moving.
My F-150, doesn't have lockouts, and doesn't turn when driving.
It just depends on the vehicle. There are so many different transfer cases and setups out there, each vehicle is different.
Got an example of your vehicle? |
|
| Back to top |
|
 |
Sinkoumn Wakeboarder.Commie


Joined: 26 Jun 2003 Posts: 1706 City: Side Lake, MN - Long Beach, CA
|
Posted: Apr 20, 2009 12:46 pm Post subject: |
|
|
I learned that when I went to get two new tires for my Denali, ended up buying 4 brand new tires  _________________ Neuston Boards
Nautiques |
|
| Back to top |
|
 |
gswake Wakeboarder.Commie


Joined: 02 Feb 2005 Posts: 1420 City: Little Rock
|
Posted: Apr 20, 2009 1:37 pm Post subject: |
|
|
haugy, would it make a difference to have the same size, but different tires? I'm thinking hypothetically, I don't have an actual example. But say for some reason you wanted different tread on the front, but got the same size?
Or would you just be screwed when it came time to rotate? _________________
| Wakebrad wrote: | | It's fun to think we know everything but we have a representative government for a reason. |
|
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Apr 20, 2009 1:39 pm Post subject: |
|
|
| gswake, you can, but like you said, rotating will be fun. |
|
| Back to top |
|
 |
DJew Jake Wakeboarder.com Freak


Joined: 17 Sep 2003 Posts: 3907 City: Toronto
|
Posted: Apr 20, 2009 2:19 pm Post subject: |
|
|
haugy, All 4 tires are the same size, they just happen to be made by a different company... So the differences between the front and back should be extremely small, I figure the transfer case is designed to handle wear differences... _________________ They know what is what but they dono what is what they just strut. |
|
| Back to top |
|
 |
chavez Ladies Man


Joined: 22 Sep 2003 Posts: 27375 City: Roseville
|
Posted: Apr 20, 2009 2:33 pm Post subject: |
|
|
DJew Jake, is this a real 4x4 or an AWD system?
So long as they are the same size tire:
If it's a real 4x4, when out of 4x4 it should be no problem. When in 4x4 it would only really be a problem on paved or very hard surfaces. Snowy or icy pavement is ok. You should not be in 4x4 on paved surfaces anyhow.
In an AWD system, this would cause somewhat higher wear on the clutch packs in the differential - don't know if you would ever see a problem though. Unless of course it was a viscous coupling in which case I don't think it would matter at all. _________________
| Quote: | | That's Mr. Gingermex to you a$$hole. |
RIP MHL 04/25/1958 - 01/11/2006 |
|
| Back to top |
|
 |
ridininmd Wakeboarder.Commie


Joined: 16 Feb 2006 Posts: 1231
|
Posted: Apr 20, 2009 2:51 pm Post subject: |
|
|
| DJew Jake wrote: | | All 4 tires are the same size, they just happen to be made by a different company... So the differences between the front and back should be extremely small, I figure the transfer case is designed to handle wear differences... |
You should be fine, just don't go doing 4 wheel drive donuts on pavement or anything. |
|
| Back to top |
|
 |
DJew Jake Wakeboarder.com Freak


Joined: 17 Sep 2003 Posts: 3907 City: Toronto
|
Posted: Apr 20, 2009 3:33 pm Post subject: |
|
|
Its 4wd not awd... Thanks for the answers thats what i figured. _________________ They know what is what but they dono what is what they just strut. |
|
| Back to top |
|
 |
Broccoli B Wakeboarder.com Freak


Joined: 12 Jul 2003 Posts: 2670 City: Grand Rapids
|
Posted: Apr 21, 2009 8:55 am Post subject: |
|
|
Your car does not know what brand of tire you have. If all 4 tires are the same size you will have no problems, in or out of 4WD. _________________ Brent B
| jt09 wrote: | | don't assume what you think i assume. you would assume wrong. |
| lcap wrote: | | you assume that i assume that my assuming is wrong and assume your assumption therefore must be correct. |
|
|
| Back to top |
|
 |
DJew Jake Wakeboarder.com Freak


Joined: 17 Sep 2003 Posts: 3907 City: Toronto
|
Posted: Apr 21, 2009 10:00 am Post subject: |
|
|
Broccoli B, Yeah so why are all the shops now refusing to replace 1 or 2 tires, they want to do all 4 stupid liabilities. _________________ They know what is what but they dono what is what they just strut. |
|
| Back to top |
|
 |
STANG KILLA SS Wakeboarder.Commie


Joined: 16 Feb 2008 Posts: 2086 City: Killeen TX
|
Posted: Apr 21, 2009 1:25 pm Post subject: |
|
|
broccoli, manufacture to manufacture have different actual diameters even though the size indicates its the same. this is very common and can be 1/2"+ in alot of cases.
only way to be sure is to actually measure the circumfrence. _________________
 |
|
| Back to top |
|
 |
Hollywood PityDaFool Who Posts This Much


Joined: 01 Oct 2003 Posts: 5601 City: Door Knob
|
Posted: Apr 21, 2009 1:29 pm Post subject: |
|
|
| DJew Jake wrote: | | Broccoli B, Yeah so why are all the shops now refusing to replace 1 or 2 tires, they want to do all 4 stupid liabilities. |
Replacing 2 warn out tires with 2 brand new tires of the same brand and size is a problem...  _________________
| dizzlestoy wrote: | | Dumb question... What is "Bubb Rubbing" I googled it and wakeboarder.com came up. |
|
|
| Back to top |
|
 |
DJew Jake Wakeboarder.com Freak


Joined: 17 Sep 2003 Posts: 3907 City: Toronto
|
Posted: Apr 21, 2009 2:57 pm Post subject: |
|
|
Hollywood, Not worn out I lost one tire non reparable my tires have 15k on them. Having too replace all 4 is insane. _________________ They know what is what but they dono what is what they just strut. |
|
| Back to top |
|
 |
JeffreyCH Wakeboarder.Commie


Joined: 11 Aug 2008 Posts: 2205 City: Lincoln
|
Posted: Apr 21, 2009 5:41 pm Post subject: |
|
|
Dude they are tryin to rip you off, I've noticed that a lot since the economy had went to crap. I had my mom drop my truck off ofr an alignment, and the scumbags saw that it was a woman, and claimed that my truck needed 900 worth of work on the front end, uhhhh no I had one blown shock. Just the other night I went to McD's and ordered 4 things from the dollar menu and the a-hole tried to tell me it was 5.28.....uuummmm no 4.28, and a few other things that have come up. Go to a different shop. _________________
| _bruky wrote: | | 99 problems but wisdom ain't one. |
|
|
| Back to top |
|
 |
jjaszkow Wakeboarder.Commie

Joined: 25 Jul 2006 Posts: 2124 City: Some Airport
|
Posted: Apr 21, 2009 7:11 pm Post subject: |
|
|
DJew Jake, personally, I'd stick with the same brand and tread pattern if at all possible. I've never had a problem bringing in a single tire and rim and asking them to mount a new tire and balance it. Make sure to mark the direction the tire goes on if you have directional tread if you are going to go that route.
I hate the non-repairable punctures . Had to buy a new tire for my wife's car a month ago due to the same issue. |
|
| Back to top |
|
 |
DJew Jake Wakeboarder.com Freak


Joined: 17 Sep 2003 Posts: 3907 City: Toronto
|
Posted: Apr 21, 2009 8:03 pm Post subject: |
|
|
jjaszkow, Thats what I did, just rolled the thing in and they changed it and i put it on myself annoying but not a big deal. _________________ They know what is what but they dono what is what they just strut. |
|
| Back to top |
|
 |
Broccoli B Wakeboarder.com Freak


Joined: 12 Jul 2003 Posts: 2670 City: Grand Rapids
|
Posted: Apr 22, 2009 3:46 am Post subject: |
|
|
STANG KILLA SS, According to the Department of Motor Vehicles for a tire to be considered "standard size" It needs to fit into one of the categories within tolerance, tolerance is + or - 3mm.
My brother is a manager at Discount Tire, they are trained to tell you that, they are half tire monkies, half saleman. _________________ Brent B
| jt09 wrote: | | don't assume what you think i assume. you would assume wrong. |
| lcap wrote: | | you assume that i assume that my assuming is wrong and assume your assumption therefore must be correct. |
|
|
| Back to top |
|
 |
pet575 Wakeboarder.com Freak


Joined: 20 Jun 2006 Posts: 3630 City: Kansas City, MO
|
Posted: Dec 17, 2009 10:26 am Post subject: |
|
|
So, did we ever decide on this "mismatching" question, or did Broccoli B settle it?
I need to replace all 4 of my tires, but I've got a full-sized spare that has never been used. It is a BFG Radial T/A and I was going to put another name brand on that is exactly the same size. Anyone think that the mismatching of tread patterns between the differing brands, despite use of exactly the same size (245/65R17) would cause a problem on my 2004 Explorer AWD? _________________
| Wakebrad wrote: | | I honestly think it has to do with internet penetration... |
|
|
| Back to top |
|
 |
dbismyname Wakeboarder.Commie

Joined: 14 Sep 2008 Posts: 1073 City: Clarksville
|
Posted: Dec 17, 2009 10:43 am Post subject: |
|
|
| Are you planning on putting one of the old tires underneath to replace the spare just to save the cost of one tire? I don't know that risking a different wear time on one tire would be worth the savings. Not to mention having an old used tire as a spare isn't too smart. |
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Dec 17, 2009 11:18 am Post subject: |
|
|
pet575, so you're talking about 3 new tires, and using the spare?
If one's at AT and the others are street radials, the AT will wear faster. Just because AT's wear faster.
But when you rotate them, and the AT is on the front it will handle weird. One AT and one radial up on the front will not give you secure and predictable handling.
I would just leave the spare as a good tire, and get 4 new ones. Besides, when you do get a flat, do you want a worn out tire as your backup?
I have 3 spares for my truck. One good one that goes with the truck. And two standby's that go with me when traveling or out camping. |
|
| Back to top |
|
 |
Dpierce37 Ladies Man


Joined: 23 Apr 2003 Posts: 7659 City: Austin
|
Posted: Dec 17, 2009 1:49 pm Post subject: |
|
|
seems to work just fine for me! HAHA
 _________________
 |
|
| Back to top |
|
 |
pet575 Wakeboarder.com Freak


Joined: 20 Jun 2006 Posts: 3630 City: Kansas City, MO
|
Posted: Dec 17, 2009 2:00 pm Post subject: |
|
|
| haugy wrote: | pet575, so you're talking about 3 new tires, and using the spare?
But when you rotate them, and the AT is on the front it will handle weird. One AT and one radial up on the front will not give you secure and predictable handling.
I would just leave the spare as a good tire, and get 4 new ones. Besides, when you do get a flat, do you want a worn out tire as your backup?
|
That WAS my plan, but I hadn't considered that handling and wear difference so I think I'll just go with 4 new. I was hoping to save the money by buying only 3. Guess the only way I can do that is to replace with BFG Rugged Trail T/A's since that is what is on there now and is what the unused spare is.
The "worn out" tires have enough tread on them to use in an emergency. Why am I confused about this? I don't see the big deal with using one of the old tires as a spare. _________________
| Wakebrad wrote: | | I honestly think it has to do with internet penetration... |
|
|
| Back to top |
|
 |
pet575 Wakeboarder.com Freak


Joined: 20 Jun 2006 Posts: 3630 City: Kansas City, MO
|
Posted: Dec 17, 2009 2:05 pm Post subject: |
|
|
Separate question:
I'm leaning toward the General Grabber simply because it is the top-rated tire for light truck/SUV use by both Consumer Reports and TireRack.com. First time, I replaced the OEM BFG Rugged Trail T/A's with the same thing. They've been decent, but they are WAY lower on the list for CR/TireRack's ratings.
Occasionally, I might park in wet grass/mud while tailgating at a K-State game or a Chiefs game. My place at the lake is a little less than a mile of gravel road. Ramps are concrete/paved anywhere I boat, so no gravel ramps to be concerned with. So, most of my driving is from suburbia to my office downtown on paved roads.
Anyone think the Grabbers are not up to snuff for what I'm doing? Should I just stick with the BFG Rugged Trail T/A's even though they are "inferior" according to CR/TireRack? _________________
| Wakebrad wrote: | | I honestly think it has to do with internet penetration... |
|
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Dec 17, 2009 2:46 pm Post subject: |
|
|
I had the grabbers with 50% tread on them. They pulled my jeep on the trailer through all kinds of muddy hell out at my friends farm in Kentucky. They get the thumbs up from me on traction.
As for the spare, I don't know how worn your current tires are. I've seen people with the same train of thought. But using their old tires that were worn down to either slicks, or into the wire thread. Just making sure you didn't do that.  |
|
| Back to top |
|
 |
pet575 Wakeboarder.com Freak


Joined: 20 Jun 2006 Posts: 3630 City: Kansas City, MO
|
Posted: Dec 17, 2009 3:08 pm Post subject: |
|
|
No, they are nowhere near slicks or exposed steel. They just need to be replaced soon is all. I think the best one of the 4 would be perfectly fine for a reliable spare. I guess the question comes down to how important the CR/TireRack ratings are to me, and if it is important enough to make me move away from Rugged Trail T/A's and require me to buy a 4th tire. Maybe I can find a "Buy 3, Get One Free" deal that makes the decision for me.
Thanks for all the feedback. _________________
| Wakebrad wrote: | | I honestly think it has to do with internet penetration... |
|
|
| Back to top |
|
 |
Commodore Ladies Man


Joined: 20 Jun 2005 Posts: 11636
|
Posted: Dec 18, 2009 6:18 am Post subject: |
|
|
pet575, go to your local tire guys, and tell them "Shop A" is doing buy 3-get-1-free.
See if they'll honor it. They are looking for business just like everyone else. Just make sure they don't rape ya on the mount and balance. That's how those shops make up the cost of that tire. |
|
| Back to top |
|
 |
|
|
|