| View previous topic :: View next topic |
| Author |
Message |
the_dude Outlaw

Joined: 09 Jul 2008 Posts: 201 City: Long Beach
|
Posted: Aug 30, 2008 2:12 pm Post subject: Help diagnosing bad vibradtion-97 VLX |
|
|
So we were out wakeboarding this moring and I noticed the vdrive oil light kicked on. Oil was a little low so we idled back to the dock and bought some oil from down the street. Put it in and light went off as soon as we put it in gear.
Idled out of the 5mph zone and planed out and noticed a bad vibration. I tried faster and slower speeds and it would get worse at higher speeds. Stoped the boat to make sure we didn't have anything dragging on the proper or rudder or anything. Planed out again and if anything the vibration was worse.
Got the boat on the trailer (sitting in water) and idled forward and in reverse. Reverse I noticed a tapping sound so I figured the vdrive was shot but when I looked at it I noticed that the prop shaft was moving really out of round. Watching it for a minute I noticed that the vdrive side of the coupling looked normal but the shaft side was definitely out of round. Where the shaft entered the packing it was really moving out of round.
Any tips or tricks to help me diagnose what the problem is? My first thought was a bent shaft somehow? If I could somehow get the parts to me I'd work all night to fix it if I had too.
Thanks |
|
| Back to top |
|
 |
|
|
K-dub Ladies Man

Joined: 12 Jan 2003 Posts: 14760
|
Posted: Aug 30, 2008 2:31 pm Post subject: |
|
|
| are the bolts that hold the shaft to the v-drive tight? |
|
| Back to top |
|
 |
the_dude Outlaw

Joined: 09 Jul 2008 Posts: 201 City: Long Beach
|
Posted: Aug 30, 2008 3:30 pm Post subject: |
|
|
| K-dub wrote: | | are the bolts that hold the shaft to the v-drive tight? |
LoL. Was just coming to post an update as I posted on the Malibu Forum.
That is the exact problem. Now how do I dial in the proper alignment when bolting it back together? |
|
| Back to top |
|
 |
K-dub Ladies Man

Joined: 12 Jan 2003 Posts: 14760
|
Posted: Aug 30, 2008 3:41 pm Post subject: |
|
|
| not much help there, but.....last time it happened to me, I just tightened one bolt a little bit, then moved across to the next (cris-crossing), if you will.....until I had them all so tight that I couldn't get any more movement on the wrench....kinda like you would do on the lug nuts on a tire. Mine was fine after that. |
|
| Back to top |
|
 |
K-dub Ladies Man

Joined: 12 Jan 2003 Posts: 14760
|
Posted: Aug 30, 2008 3:49 pm Post subject: |
|
|
| just talked to my mechanic....he said just tighten them down and you should be golden. Nothing else necessary |
|
| Back to top |
|
 |
the_dude Outlaw

Joined: 09 Jul 2008 Posts: 201 City: Long Beach
|
Posted: Aug 30, 2008 4:33 pm Post subject: |
|
|
| just finished, I'm off to the ramp... |
|
| Back to top |
|
 |
the_dude Outlaw

Joined: 09 Jul 2008 Posts: 201 City: Long Beach
|
Posted: Aug 30, 2008 7:42 pm Post subject: |
|
|
The boat is fixed!!
Thanks for calling your mechanic. We got a couple more sets in for everyone tonight!
YESSSSS! |
|
| Back to top |
|
 |
JUST-IN-TIME Soul Rider

Joined: 24 Dec 2007 Posts: 356 City: ON YOUR BOAT
|
Posted: Sep 01, 2008 2:24 pm Post subject: |
|
|
better check that aliment now
and change to nyloc stainless nuts and lube them up with marine grease
not the first malibu i have seen that had done that _________________ HUMAN BUILT = HUMAN FIXED
CERTIFIED MARINE/PWC TECHNICIAN
www.switchbait.com |
|
| Back to top |
|
 |
|
|
|