| View previous topic :: View next topic |
| Author |
Message |
jryan15 Newbie

Joined: 20 Jul 2008 Posts: 23
|
Posted: Jul 21, 2008 7:27 pm Post subject: Finding RPM lead when using smartcraft gages. |
|
|
I've been thinking of added a perfect pass system to my 2004 sea ray which has smartcraft gages. I was wondering if anyone could tell me where I can get a tach feed off of the gages or engine with this setup. The engine looks to have an electronic ignition system. The engine is the 5.0L model.
Thanks! |
|
| Back to top |
|
 |
|
|
JUST-IN-TIME Soul Rider

Joined: 24 Dec 2007 Posts: 356 City: ON YOUR BOAT
|
Posted: Jul 23, 2008 12:23 pm Post subject: |
|
|
grey wire is the tach readout
comes off the ecu
u have tbolt v ignition _________________ HUMAN BUILT = HUMAN FIXED
CERTIFIED MARINE/PWC TECHNICIAN
www.switchbait.com |
|
| Back to top |
|
 |
jryan15 Newbie

Joined: 20 Jul 2008 Posts: 23
|
Posted: Aug 23, 2008 7:29 pm Post subject: |
|
|
Thanks for the advice, but I didn't get the RPM readout to work on the perfect pass unit. I found a gray wire in one (left side) of the two connectors that plugged into a module on top of the engine. I assume that was the ECU...
The perfect pass RPM cable has a black and gray lead. I connected the gray to the gray wire at the engine and I just tied the black to the grounding block under the dash. I was wondering if maybe I need to connect to a direct ground lead off of the ECU itself... |
|
| Back to top |
|
 |
JUST-IN-TIME Soul Rider

Joined: 24 Dec 2007 Posts: 356 City: ON YOUR BOAT
|
Posted: Aug 23, 2008 7:37 pm Post subject: |
|
|
what colors are coming off the dash tach???
i have all the manuals for the smartcraft stuff _________________ HUMAN BUILT = HUMAN FIXED
CERTIFIED MARINE/PWC TECHNICIAN
www.switchbait.com |
|
| Back to top |
|
 |
jryan15 Newbie

Joined: 20 Jul 2008 Posts: 23
|
Posted: Aug 24, 2008 6:42 am Post subject: |
|
|
Thanks. All my gages are daisy chain connected with the same three wires red, yellow, blue...
My distributer cap is not the normal round style, it's flat with the spark plug connectors coming out of the sides. The is a coil has a three pin connector going to it with the following wires.
1. Pink with white stripe
2. White with green stripe
3. White with green stripe (again)
I would imagine that one of them is a tach lead, but I don't want to go stabbing at them without knowing more.
Also the flat distributer also has a three pin connector coming off of it. There is nothing plugged into it. I guess it was for systems with an integrated coil or something... |
|
| Back to top |
|
 |
jryan15 Newbie

Joined: 20 Jul 2008 Posts: 23
|
Posted: Aug 24, 2008 10:53 am Post subject: |
|
|
| Got it working! The tach is working after connecting to the middle white with green striped wire that I mentioned in the earlier post... |
|
| Back to top |
|
 |
JUST-IN-TIME Soul Rider

Joined: 24 Dec 2007 Posts: 356 City: ON YOUR BOAT
|
Posted: Aug 24, 2008 3:57 pm Post subject: |
|
|
cool
merc changed a bunch of tings around since going smartcraft _________________ HUMAN BUILT = HUMAN FIXED
CERTIFIED MARINE/PWC TECHNICIAN
www.switchbait.com |
|
| Back to top |
|
 |
|
|
|