View previous topic :: View next topic |
Author |
Message |
wakebelews Newbie
Joined: 03 Sep 2008 Posts: 13 City: winston-salem
|
Posted: Sep 03, 2008 3:53 pm Post subject: Binding Problem |
|
|
I currently ride a 07' liquid force diva with fusion binding. I have had the set up for just about a year. Resently i've noticed that there was a small gap between the binging and the board. On monday there was about a two finger gap from the top board and the bottom of the binding. Everything is on tight and no bolts are loose. Is there any way that you can fix it or do you just have to deal with it? |
|
Back to top |
|
|
|
Trucker T Soul Rider
Joined: 28 Jul 2004 Posts: 416 City: Washington, DC And I'm a Lady damnit!
|
Posted: Sep 04, 2008 11:47 am Post subject: |
|
|
It sounds like your screws may be too long for the holes that are dug out on your board, therefore not pulling your bindings all the way down to your board. You may have to order smaller screws so they don't allow a gap. There definitely shouldn't be a gap. |
|
Back to top |
|
|
wakebelews Newbie
Joined: 03 Sep 2008 Posts: 13 City: winston-salem
|
Posted: Sep 04, 2008 3:02 pm Post subject: |
|
|
Its clamped down all the way with the screws that hold it onto the board. But just incase what size would be good? |
|
Back to top |
|
|
SeaLyon Addict
Joined: 18 Aug 2006 Posts: 549 City: Counce (Pickwick)
|
Posted: Sep 06, 2008 5:44 am Post subject: |
|
|
wakebelews, Your mounting plate could be warped, take the boot off and put it on a flat surface. if it doesn't sit flat I would see about warrenty returns. _________________ In God We Trust
www.sealyon.net
www.sealyon.net |
|
Back to top |
|
|
wakebelews Newbie
Joined: 03 Sep 2008 Posts: 13 City: winston-salem
|
Posted: Sep 06, 2008 11:16 am Post subject: |
|
|
Thanks. That might be the problem. But, I dont have the warrenty anymore. I am going to try to go by the shop today and see about possibly getting new binding. |
|
Back to top |
|
|
bendress Newbie
Joined: 08 Jul 2009 Posts: 2
|
Posted: Jul 10, 2009 9:46 am Post subject: |
|
|
Perhaps you folks could provide some insight on my binding issue as well!
I just picked up an LF Diva/08 Prima Bindings package and the thumbscrews were a pain to screw in. Had a friend take a look and now I don't think that I can get them back off as the top of the thumb screw turns, but the actual screw part doesn't move. My fault for letting someone else do it, but any advice on loosening these would be much appreciated! |
|
Back to top |
|
|
flixmaster Site Owner
Joined: 30 Oct 2003 Posts: 7487
|
Posted: Jul 10, 2009 10:00 am Post subject: |
|
|
Scrape some of that blue stuff off the screw threads. LF puts more thread lock on the binding screws than needed. This causes the thumb screws to really be hard to tighten.
Use a razor blade to get the stuff off just be careful not to cut yourself. _________________ Wakeskating
Ronix Wakeboards
Wakeboarding |
|
Back to top |
|
|
bendress Newbie
Joined: 08 Jul 2009 Posts: 2
|
Posted: Jul 10, 2009 12:16 pm Post subject: |
|
|
I'll give it a try! Thanks for the info! |
|
Back to top |
|
|
|
|