| View previous topic :: View next topic |
| Author |
Message |
petie335 Newbie

Joined: 19 Aug 2008 Posts: 4 City: PULLman
|
Posted: Aug 19, 2008 4:57 pm Post subject: Boat overheating- New impeller & thermostat Im stumped |
|
|
1992 OMC Cobra 4.3L V6
It all started with my boat running a little hot around 190. I replaced the impeller and started it using a fake a lake set up. I watched it for a while and the temp went up to 190 and surpassed that.
After that I thought it was the thermostat. I pulled that out and wasn't able to get a new one for sometime so I just left it open so I could check if it was a thermostat issue. When I removed the thermostat I took off the hoses to the manifolds and they drained.
Once I started it up I noticed a squeaking coming from the water pump that wasn't there before I replaced the thermostat and drained the exhaust manifolds. I ran it for about 30 seconds and noticed that it wasn't cooling so I shut it off and and checked the manifolds. There wasn't any water at all.
So I went back to the impeller and made sure it was set right and started it up. I did this multiple times and there still wasn't any water in the engine...I'm stumped...
I'm also pretty sure the water pump is still good. It's not leaking and I pulled off one of the hoses and it was pushing water...This was before the manifolds were drained.. |
|
| Back to top |
|
 |
|
|
bftskir Outlaw

Joined: 14 Jul 2008 Posts: 118
|
Posted: Aug 19, 2008 5:10 pm Post subject: |
|
|
| if the impeller you took out had lost fins...they are stuck in your system try to back flush them out, sounds like you have a blockage. |
|
| Back to top |
|
 |
petie335 Newbie

Joined: 19 Aug 2008 Posts: 4 City: PULLman
|
Posted: Aug 19, 2008 5:28 pm Post subject: |
|
|
| The old impeller had 2 or 3 lost fins but i'd imagine that there would be some water flow if it was a block. There isn't any. But how do you go about back flushing? |
|
| Back to top |
|
 |
pet575 Wakeboarder.com Freak


Joined: 20 Jun 2006 Posts: 3630 City: Kansas City, MO
|
Posted: Aug 20, 2008 9:40 am Post subject: |
|
|
If the back flushing doesn't solve it (I bet it does), then I'd start looking at the water pump housing itself. Maybe the bearing is bad, which is causing the noise you're hearing. _________________
| Wakebrad wrote: | | I honestly think it has to do with internet penetration... |
|
|
| Back to top |
|
 |
bftskir Outlaw

Joined: 14 Jul 2008 Posts: 118
|
Posted: Aug 20, 2008 9:49 am Post subject: |
|
|
I am not as familiar with IO's as inboards, but follow your hose off the pump and the pieces will be "downstream" in the oil cooler is usually as far as they get...but the point is those pieces are in there somewhere...
no water at all is getting in? thats weird. wish I could be more help. |
|
| Back to top |
|
 |
petie335 Newbie

Joined: 19 Aug 2008 Posts: 4 City: PULLman
|
Posted: Aug 20, 2008 2:19 pm Post subject: |
|
|
| I think the noise in the water pump is due to no water being present because before the manifolds were drained there wasn't that noise. But I will try back flushing today and see what happens. |
|
| Back to top |
|
 |
petie335 Newbie

Joined: 19 Aug 2008 Posts: 4 City: PULLman
|
Posted: Aug 20, 2008 4:40 pm Post subject: |
|
|
| Ok I back flushed it and I couldn't find anything. I really am stumped and don't know what else to try. This seems so ridiculous considering it was running better with an impeller with 3 fins. Ah, so frustrated. |
|
| Back to top |
|
 |
JUST-IN-TIME Soul Rider

Joined: 24 Dec 2007 Posts: 356 City: ON YOUR BOAT
|
Posted: Aug 24, 2008 12:01 am Post subject: |
|
|
well u got an oil cooler in there, i bet the fins are in there
when i do those drive mounted pumps, i buy the kit with housing
the engine mounted pump is just for circulation for the motor, but it has to get there from the drive pump
so pull the inlet hose ans see if ur getting water
if not, then u installed something wrong or u fried the new pump already _________________ HUMAN BUILT = HUMAN FIXED
CERTIFIED MARINE/PWC TECHNICIAN
www.switchbait.com |
|
| Back to top |
|
 |
blaydeman Outlaw


Joined: 03 Jun 2006 Posts: 119
|
Posted: Aug 26, 2008 7:54 am Post subject: |
|
|
| slipping belt? does the impeller spin freely? |
|
| Back to top |
|
 |
JUST-IN-TIME Soul Rider

Joined: 24 Dec 2007 Posts: 356 City: ON YOUR BOAT
|
Posted: Aug 26, 2008 2:38 pm Post subject: |
|
|
the water pump is in the drive guys
the circulation pump is on the motor
over the years i have not seen a bad circulation pump no circulate, just weep out of the whole _________________ HUMAN BUILT = HUMAN FIXED
CERTIFIED MARINE/PWC TECHNICIAN
www.switchbait.com |
|
| Back to top |
|
 |
|
|
|