| View previous topic :: View next topic |
| Author |
Message |
skinautique1985 Outlaw

Joined: 26 Feb 2003 Posts: 140 City: Yuba CIty,CA
|
Posted: Jan 09, 2007 6:38 pm Post subject: 2001 SAN Subwoofer location |
|
|
| Anyone have any pics of what they have done? i'm trying to figure out a way to get a 10W7 somewhere in the boat and i'm coming up a little short on ideas, there just isnt that much room under the passenger console due to the ice chest/glove box
|
|
| Back to top |
|
 |
|
|
frymantcu Outlaw


Joined: 18 Apr 2005 Posts: 111 City: Fort Worth
|
Posted: Jan 11, 2007 9:26 am Post subject: |
|
|
| That's gonna be the only place to really fit it, I have a bazoka(sp?) tube in there now which hits horrible. The only other place would have to remove the kickpanel on the drivers side but that might kill your leg room. I have the amp for my tower speakers in there and thats okay but a full sub box might be tight. I plan to build a box under the passenger console and extending it up the bow to port it. I'd surf over to PlanetNautique.com for better advice. Good luck let us know how it works our.
|
|
| Back to top |
|
 |
jwat142 Wakeboarder.Commie

Joined: 14 Jan 2003 Posts: 1009
|
Posted: Jan 13, 2007 5:43 am Post subject: |
|
|
| I have a '97 Super Sport, which is prett similar to your boat. I fit a 12" sub in the boat where the kick panel goes and I have plenty of room. You just have to custom make the box so you can push it as far back as possible.
|
|
| Back to top |
|
 |
Sinkoumn Wakeboarder.Commie


Joined: 26 Jun 2003 Posts: 1706 City: Side Lake, MN - Long Beach, CA
|
Posted: Jan 13, 2007 8:43 am Post subject: |
|
|
Jwat, did you install it behind the kick panel? Or did you set it into the actual kickpanel, where the cone faces the driver and is open to the air?
Post up a pic if you can, I'm trying to figure where I will put my 10'' (hopfully behind the kick panel as well, but will need to relocate the heater core somehow...) - 97 SSN as well.
_________________ Neuston Boards
Nautiques |
|
| Back to top |
|
 |
jwat142 Wakeboarder.Commie

Joined: 14 Jan 2003 Posts: 1009
|
Posted: Jan 13, 2007 9:01 am Post subject: |
|
|
I actually removed the factor kick panel all together. I then made a custom box and the front of the box is now the new kick panel. The box is enclosed in the back, which I would recommend you doing. If you leave it open to the air, you won't get near the bass response. Below is the only picture I have of the box in the boat.

|
| Description: |
|
| Filesize: |
65.21 KB |
| Viewed: |
2915 Time(s) |
|
|
| Back to top |
|
 |
Sinkoumn Wakeboarder.Commie


Joined: 26 Jun 2003 Posts: 1706 City: Side Lake, MN - Long Beach, CA
|
Posted: Jan 13, 2007 9:57 am Post subject: |
|
|
Right on, I thought that was you (wakeside rides). When you installed the new kick panel, did you move it forward any, or did you just reinstall it to the orignal mounting location?
Aha, I understand the point of the box for the sub, but is there any benefit to having the sub facing out into the boat as opposed to underneath the front playpen (more walls for sound to bounce on?).
That really sounds stupid I guess, it's hard to conceptualize that through typing - but basically, does it sound the same with the way you mounted it as opposed to putting the box behind the kick panel (not using the kick panel as the mount/front of the sub enclosure?
_________________ Neuston Boards
Nautiques |
|
| Back to top |
|
 |
jwat142 Wakeboarder.Commie

Joined: 14 Jan 2003 Posts: 1009
|
Posted: Jan 13, 2007 12:54 pm Post subject: |
|
|
| The new kick panel sits a little farther forward than the original, but not much. I had to put it a little farther forward so I could make the box big enough for the sub. As far as which way to face the sub...as long as it is enclosed in a box, it should be fine being faced out like mine. I honestly don't know a ton about audio stuff though, so this may be a better question for someone else.
|
|
| Back to top |
|
 |
frymantcu Outlaw


Joined: 18 Apr 2005 Posts: 111 City: Fort Worth
|
Posted: Jan 17, 2007 1:23 pm Post subject: |
|
|
| jwat142, did you fit the amp in that area too? Looks good either way..
|
|
| Back to top |
|
 |
jwat142 Wakeboarder.Commie

Joined: 14 Jan 2003 Posts: 1009
|
Posted: Jan 17, 2007 5:08 pm Post subject: |
|
|
| No, I mounted the amp on the wall under the passenger seat. I used liquid nails to glue wood onto the side wall and then I screwed the amp into the wood. I carpeted the wood so it matched the carpet on the side wall.
|
|
| Back to top |
|
 |
Sinkoumn Wakeboarder.Commie


Joined: 26 Jun 2003 Posts: 1706 City: Side Lake, MN - Long Beach, CA
|
Posted: Jan 17, 2007 8:39 pm Post subject: |
|
|
jwat142, did you get the carpet from a dealer? Do you recall the cost? I've been looking to get some, but have been busy/lazy and not called around.
Also, what type of Liquid nails did you use to adhere the wood amp board to the hull fiberglass?
_________________ Neuston Boards
Nautiques |
|
| Back to top |
|
 |
jwat142 Wakeboarder.Commie

Joined: 14 Jan 2003 Posts: 1009
|
Posted: Jan 18, 2007 6:44 am Post subject: |
|
|
I just bought marine carpet from the local Lowe's. It didn't match perfect, but it is pretty close. I attached a pic of the amp mounted to the wall. I actually have a different amp there now, but it's set up the same way.
I honestly can't remember which liquid nails I used. Just read the bottle and pick the best one. All of that stuff sticks like crazy, so it shouldn't be a big deal.
Here is a link to my boat on wakesiderides.com: http://www.wakesiderides.com/rides/index.php?page=out&id=624. You can see some bigger pictures on there.

|
| Description: |
|
| Filesize: |
3.9 KB |
| Viewed: |
2757 Time(s) |
|
|
| Back to top |
|
 |
|
|
|