| View previous topic :: View next topic |
| Author |
Message |
kevthayer Outlaw


Joined: 12 Sep 2005 Posts: 231 City: Benicia
|
Posted: Dec 20, 2006 1:17 pm Post subject: Mercruiser 350 heats uup on one side of the block |
|
|
Last week I was winterizing my boat and discovered something that makes me a little nervous. Once the engine is warmed to operating Temp (175 degrees) you can place your hand on the starboard side of the exhaust manifold and it is ice cold. Place your hand on the port side manifold and it is almost to hot to leave your hand on for more than a few seconds.
I am hoping that all this is the direction of water flow which hopefully means that the water is just warmed up after running through the block resulting in a difference in temperature.
I hope that it is not a blockage, or ???????? If you have any insight or experience with this matter please let me know. |
|
| Back to top |
|
 |
|
|
tball Wakeboarder.com Freak


Joined: 24 Feb 2004 Posts: 3953
|
Posted: Dec 20, 2006 1:34 pm Post subject: |
|
|
they should both be cool to the touch...sounds like you might have some kind of blockage...not sure where to go from here though. _________________
| GOB Bluth wrote: | | It's a jetpack, Michael. What could possibly go wrong? |
|
|
| Back to top |
|
 |
Gmcc Newbie

Joined: 04 Jun 2006 Posts: 22 City: Gambrills
|
Posted: Dec 20, 2006 6:02 pm Post subject: |
|
|
You didn't mention the age of the motor and if you are using it in salt or brackish water. Replacing the high rise manifolod is not uncommon for engines used in salt water. I would get about 5 or 6 years out of a set on my old Donzi. It is a very simple repair. As said before both should be only slightly warm and you should be able to leave your hand on top with no discomfort. I have used Osco before
http://www.oscomotors.com/ They make replacements for just about everything. You can check your riser by unbolting it and doing a visual inspection. Soak the bolts with PB Blaster for a day or so first. If the boat is fresh water only, it might be something else blocking the flow, but I would check for rust in the riser. |
|
| Back to top |
|
 |
kevthayer Outlaw


Joined: 12 Sep 2005 Posts: 231 City: Benicia
|
Posted: Dec 20, 2006 8:39 pm Post subject: |
|
|
| The boat has about 200 hours. I bought it with 100 hours and have only had it in fresh water. There isnt a spec of rust visible on the engine but that doesnt necessarily mean that nothing is going on internally. I am thinking that it may be some sort of blockage. I did take it out on the Dirty Delta (near Stockton)a couple of times late in the season, my speedo was plugged so it is possible that something was sucked up when that happened. If it were a blockage where should I start to look? How do I take the riser off? I was a little unclear about that. Thanks for the replies. |
|
| Back to top |
|
 |
Gmcc Newbie

Joined: 04 Jun 2006 Posts: 22 City: Gambrills
|
Posted: Dec 21, 2006 3:02 am Post subject: |
|
|
| 200 hours is not much. Hard to say where the blockage is. The riser is bolted to the manifold with four bolts. Check the Osco site. Go to Mercruiser and then page 14 is the 350 page. You will need to replace the gasket when you take it apart. I had one get so hot it melted teh rubber boot coming off the back of the riser. Other things to check, Is the engine running OK? If the timing is off it can cause overheating but I would expect it to be both sides. When you were winterizing, were you in the water or on a hose? If it was a hose was there enough pressure? Is this an inboard or an I/O? |
|
| Back to top |
|
 |
kevthayer Outlaw


Joined: 12 Sep 2005 Posts: 231 City: Benicia
|
Posted: Dec 21, 2006 9:01 am Post subject: |
|
|
| Gmcc, The engine is running great. Smooth as can be ans started right up even after sitting for 2 months on the side of my house. Timing is fine, I havent adjusted it since I had a mechanic look it over when I bought it. I am a big believer if it isnt broken dont fix it. When I was winterizing I was on a hose. As for the pressure I think it was fine I had the wter turned all the way up and it was flowing out nice and warm. I thought that the intake on a boat was a draw not a pressure feed, isnt that waht the impeller is for. I could be wrong though. This is a Reinell I/O with the Alpha outdrive. |
|
| Back to top |
|
 |
Gmcc Newbie

Joined: 04 Jun 2006 Posts: 22 City: Gambrills
|
Posted: Dec 21, 2006 5:58 pm Post subject: |
|
|
| I am also a big believer of "if it isn't broken" I burned up two impellers on outdrives while they were on the "earmuffs". I am on a well and the water pressure is not super. The earmuffs all say idle speed only and only for a short time for a reason. You may want to do a visual inspection on the impeller. Rather then look for trouble in the riser, you may want to wait until the spring and put the boat back in the water to see if you really have a problem. I know the uncertainty would bug me all winter, but why go digging in the engine if you are not sure something is wrong. |
|
| Back to top |
|
 |
mneal Outlaw

Joined: 28 Jun 2003 Posts: 120 City: St. Petersburg
|
Posted: Dec 24, 2006 8:50 am Post subject: |
|
|
| Is the water in water with unlimited water supply or running on muffs? If it is on muffs and flushing it is 100% normal. The reduced water pressure causes less water to go to the port side riser. If you are saying it does that while in the water, would check the water flow, replace the impeller as a start. |
|
| Back to top |
|
 |
Ruune Wakeboarder.Commie


Joined: 19 Oct 2003 Posts: 1809 City: San Antonio & Austin, TX
|
Posted: Jan 05, 2007 8:30 am Post subject: |
|
|
when was the last time you changed the impeller for the water pump? Were there any pieces missing? Sounds like you've got some pieces of a worn impeller blocking your cooling system on one side. _________________ I eat Vegans. Medium-Rare.
American by birth, TEXAN by the grace of God.
Dyslexics of America UNTIE!!!
www.360wakeboard.com
www.texaswakeboarders.com |
|
| Back to top |
|
 |
|
|
|