| View previous topic :: View next topic |
| Author |
Message |
polkaking27 Outlaw

Joined: 31 Jul 2004 Posts: 142 City: Vancouver
|
Posted: Jan 12, 2005 9:02 pm Post subject: any ideas??? on a supersport |
|
|
| I am trying to get a spark from my '97 supersport that has been submerged. I was told by someone that I needed to replace the harness and ecm. so I replaced the harness and still no spark. I thought when starting, the distributor was controlling the spark. Am I wrong, should I spend the $600 to see if the ecm is the problem, or does anyone have any ideas??? |
|
| Back to top |
|
 |
|
|
Laptom Outlaw

Joined: 22 Nov 2003 Posts: 219 City: Eindhoven
|
Posted: Jan 13, 2005 2:39 am Post subject: |
|
|
Can you tell us something more... On what places you've got power (distributor, coils, the ECM itself, etc). Would it be possible to borrow somewhere a ECM? A dealer maybe? Do you have a electrical layout/wiring diagram of the gt40? If you mail it, I can probably give you some advice.
Good luck, Tommy |
|
| Back to top |
|
 |
polkaking27 Outlaw

Joined: 31 Jul 2004 Posts: 142 City: Vancouver
|
Posted: Jan 13, 2005 7:10 am Post subject: |
|
|
Tommy,
I have power to the coil, I know that. I'm not sure how to check the distributor or the ecm... do you know. I didn't think of borrowing an ecm, I will see if the dealer has something I can borrow. I can't find a wiring diagram of the gt-40. I have both the manuals and neither one of them have a engine wiring diagram. Thanks for the help and if you get any other ideas i'm happy to hear them |
|
| Back to top |
|
 |
El' Presidente Outlaw

Joined: 24 May 2004 Posts: 145 City: Jacksonville
|
Posted: Jan 13, 2005 9:50 am Post subject: |
|
|
Are you sure you have power coming out of the coil? If so, you can place the rotor just before TDC, loosen the distributor, turn the ingition on, remove the #1 plug wire from the distributor cap, place a test light probe in opening and ground it out and turn the distributor body clockwise and see if the light comes on. If so, you have juice from your coil passing through your distributor. Then continue to work forward. If no light, work backwards. What year SUperSport? Does the distributor have an external mounted condenser? _________________ It's a natural poke |
|
| Back to top |
|
 |
polkaking27 Outlaw

Joined: 31 Jul 2004 Posts: 142 City: Vancouver
|
Posted: Jan 14, 2005 6:28 pm Post subject: |
|
|
| el presidente- I don't know if power is coming out of the coil, I just know that it is not bad... it tests well off the boat. how do I place the the rotor just before tdc... does it matter what cylinder its on. I'll try to do that and also test the coil. Thanks |
|
| Back to top |
|
 |
polkaking27 Outlaw

Joined: 31 Jul 2004 Posts: 142 City: Vancouver
|
Posted: Jan 18, 2005 10:40 am Post subject: |
|
|
Ok, I tested the coil on the boat, and I'm getting nothing out of it. I had primary and secondary resistance tests done to it, and it was on the bare minumum on both of those test... could that be the problem. Other than that, I checked the power to the coil and the 2 prong pin is getting power when the power is on, but I'm still not getting anything out of the coil. Would this problem be the ecm, or since the coil is on the bare minumums do you think it would be the coil???
Thanks for your help |
|
| Back to top |
|
 |
vette74 Wakeboarder.Commie


Joined: 30 Jul 2003 Posts: 2144 City: Houston
|
Posted: Jan 18, 2005 11:07 am Post subject: |
|
|
I would replace the coil first they are pretty cheap especially if it is on the bare minimum of both tests. _________________ There'll be two dates on your tombstone/ And all your friends will read 'em/ But all that's gonna matter is that little dash between 'em... |
|
| Back to top |
|
 |
El' Presidente Outlaw

Joined: 24 May 2004 Posts: 145 City: Jacksonville
|
Posted: Jan 18, 2005 1:53 pm Post subject: |
|
|
polkaking27- go for the new coil purchase. If the new coil does not cure your no spark issue, try what I described above. You can determine TDC by checking the notch on the flywheel is in line with the split in the case (where the two halves bolt together) and making sure the rotor is pointing towards the small notch on top of the distributor body. Although TDC and the #1 cylinder are not necessary to check the spark, I prefer it because you know where the motor is at during stroke and you have little chance of screwing up your timing. Does youor distributor have an external mounted condenser (small round cylinder with a single wire coming out of it)? If so, check it. This is a $5.00 part that will cause you many headaches. _________________ It's a natural poke |
|
| Back to top |
|
 |
Laptom Outlaw

Joined: 22 Nov 2003 Posts: 219 City: Eindhoven
|
Posted: Jan 19, 2005 1:58 am Post subject: |
|
|
Polaking27, you said before before that you don't get a spark, but you get good voltage to the coil. To be sure the following explenation, I'm sure you're already knowing it.
The setup is pretty simple; 12V to the coil; boost the voltage; bringing the boosted voltage to the distributer by a thick cable (same as a spark cable); distribute the voltage by the distributer to all eight cilinder (in the right order). I don't know if in a '97 GT40 the distributer is mechanicaly controlled (by a breakerless contact) or electronic (ECM) controlled. If the first is the case; only 3 things can be wrong 1) the coil ($60,-) 2) the thick spark and coil wires ($40,-) or the breakerless ignition ($100,-).. If the latter is the case; still 3 things can be wrong, the same first 2 as in the first case, but also the ecm can be wrong.
I suggest switching the coil and sparkwires never can do any harm. Expecially if you're boat has been submerged. Exchange the spark wires with plugs one-by-one because the order is important.
Good luck |
|
| Back to top |
|
 |
polkaking27 Outlaw

Joined: 31 Jul 2004 Posts: 142 City: Vancouver
|
Posted: Jan 19, 2005 8:37 am Post subject: |
|
|
| thanks all for your help!!!!!!!! I was able to finally get a spark yesterday. It was the pickup coil in the distributor, LAPTOM is that the same as the breakerless ignition? I figured it had to be so i replaced it. So this leads to another question. I had to pull the distributor out to get the coil out, once i had it out my friend accidentelly cranked the motor... So I'm sure all timing is lost. Is there an easy way to time the engine or is it worth it to take it to a shop and pay them to do it? |
|
| Back to top |
|
 |
Wakebrad Ladies Man


Joined: 11 Dec 2003 Posts: 12257 City: Dallas
|
Posted: Jan 19, 2005 8:53 am Post subject: |
|
|
| polkaking27, I had that exact same problem with my '81 Bronco... stupid pickup coil. How did you figure it out? I had to take mine to the shop to get it diagnosed. |
|
| Back to top |
|
 |
polkaking27 Outlaw

Joined: 31 Jul 2004 Posts: 142 City: Vancouver
|
Posted: Jan 19, 2005 10:40 am Post subject: |
|
|
| wakebrad I just kept following the problem backwards, and it led to that, plus I had had a frind that suggested the pickup coil... Hallelujah!!! now its just the problem of timing the engine.[/b] |
|
| Back to top |
|
 |
vette74 Wakeboarder.Commie


Joined: 30 Jul 2003 Posts: 2144 City: Houston
|
Posted: Jan 19, 2005 10:44 am Post subject: |
|
|
Pull the all the spark plugs out of the engine crank over the engine with a socket.
Put your finger over the spark plug hole for the #1 cylinder.
Crank over until pressure starts to build up against your finger.
Look down at the harmonic balancer for the timing mark, keep cranking it over until that mark meets your tab on the timing cover at 0 degrees.
Your motor is now in TDC.
Put your distributor in so the rotor is about 10 deg before the #1 spark plug terminal on you distributor.
(Note you might have to take a screwdriver and turn your oil pump shaft to get your distributor to line up.)
Your engine should start get a timing light and adjust to factory specs. _________________ There'll be two dates on your tombstone/ And all your friends will read 'em/ But all that's gonna matter is that little dash between 'em...
Last edited by vette74 on Jan 19, 2005 10:44 am; edited 1 time in total |
|
| Back to top |
|
 |
Laptom Outlaw

Joined: 22 Nov 2003 Posts: 219 City: Eindhoven
|
Posted: Jan 19, 2005 10:44 am Post subject: |
|
|
Oh boy... Glad you found the problem, but you're great in creating a new one . It's not that hard for setting the timing correct, but I have to say that even I got it wrong once. I got a full 360 degrees (setting the timing at a open port) off..
I suggest to take it to a dealer or a ford car dealer. They should take care of it within 5-10 minutes so it's not that expensive.
Tommy |
|
| Back to top |
|
 |
polkaking27 Outlaw

Joined: 31 Jul 2004 Posts: 142 City: Vancouver
|
Posted: Jan 20, 2005 9:15 am Post subject: |
|
|
| vette74 thanks for the know how, I think it sounds like it might be worth it to run it by a dealer and have them do it quickly. Thanks for everyones help |
|
| Back to top |
|
 |
|
|
|